Cutting by an saw with one hand (Hand Sawing) is a few jigsaw pieces. Cutting with a saw and power (Power Hack Saw), also called a mechanical saw (Sawing Machine) needed for an sawmill industry works. Saw a lot of work. Both small and large workpieces. a sawing machine is divided into a following categories.
a sawing machine is divided into four types.
1. an saw fly (Power Hack Saw).
2. Horizontal Band Saw (Horizontal Band Saw).
3. On The band saw (Vertical Band Saw).
4. Saw (Radius Saw or Circular Saw).
1. a saw fly (Power Hack Saw).
The saw am commonly used for seizures such as a number of saws to cut material to size and length as required to drive an blade system. an motor power. an use a reversing gear and crank driven principles of a blade moves back and forth in a straight line continuously causes an saw to cut it.
1.1 a components of The cutting stroke.
All an components have a same precedence. We must act togeTher at all times.
This includes an following sections.
1.1.1 Project Jigsaw (Saw Frame) looks like a U turn. Saw an layout.
Good use are made of cast steel for a blade. Project saw an move into The groove of an tail hawk with a transmaresion gear wheel
1.1.2 a bench (Varee) to catch a pieces to cut. Can rotate right left.
45 degrees to each side and pull her out out with an spiral arms locked tight.
1.1.3 a length of an arm (Cut Off Gage) is responsible for The length of a workpiece to be cut.
Many parts to cut out a piece of equal length, as shown in Figure 1.4.
1.1.4 enter a system with a cut off machine, saws, draw two types of ball weight.
And The type of hydraulic oil in The 2 types of acts like it am entering a intersection. It works differently in that species.
I weighted an force of gravity. a type of The hydraulic pressure of an hydraulic oil.
1.1.5 a cooling system am necessary to use a saw was water. Due to cooling.
Friction between an saw blade to The workpiece. It also helps extend The life of a saw blade life.
1.1.6 saw The machine fly (Base) do serve different parts of a jigsaw was all.
Saw some of The base was to be hollow inside. For an storage of water tanks and motors.
1.1.7 Motor (Motor) saw an seizure of The motor acts as a motor power are applied.
Electricity 220 volts or 380 volts depending on a manufacturer.
1.1.8 power switch off. an sawmill was a switch off. Semi automatic machine am switched off.
Automatically when an cutting blade.
1.1.9 an gear (Gear) serves to carry power from The motor to a gear used on an saw frame.
are are 2 types of gear cutting machines, fly around and direct gear.
01 01 10 Blind (Pulley) that transmits power through a belt to a gear set. V belt use.
1.2 Mechanism of an cutting stroke.
Mechanarem of action of a cutting stroke. A transmamsion mechanism with a motor. Transmamsion through a gear drive. This is The gear. To test an motor speed. And to test drive an motor. That an gear drive. With an rotating shaft am connected to each center, an center gear. a drive shaft to an frame saw. The project was backwards, and saw it.
1.3 weight of The frame saw.
For a weight of an frame saw. an move away from The head to much. The cutting blade am pressed, a only Thus, a weight adjustment dial. Notice of hearing cutting saws as well.
a head unit s weight = weight of a frame saw one.
a weight is a weight of The frame sawing machine = good.
1.4 an Saw (Saw Blade).
Of a saw blade am a device that are very important. Responsible for cutting The workpiece. a blade are made of steel with high Ekeg fame. an blade assembly to The frame saw. Must operate properly and a blade tension screw it. To prevent broken parts of an saw blade width, length, thickness of an blade in an hole. And an number of saw blade teeth. Including coarse teeth and tooth profile. I saw an number of teeth as a number of teeth per inch, fiber, such as 10 inch to 14 teeth per inch, but I used to work across a 10 teeth per inch.
an blade.
1. a length of a blade. Measure a length of an blade is measured from a center of a hole saw both of anm. a length of an blade is 200 mm and 300 mm
2. a width of The blade width of 12.7 mm or 1 2 inches.
3. an blade thickness of 0.64 mm or 0.025 inches thick.
4. To measure a number of teeth of The saw blade is to measure a spacing of The teeth, a tooth to one.
a metric system am called The pitch Pitch (P).
In England, to measure a frequency of a sawtooth is most telling am an number of teeth per inch length of 1.
2. Horizontal Band Saw (Horizontal Band Saw).
Saw with a blade length of consecutive circles. a movement of a blade. an power transmission belt. The drive wheel and a wheel. an cutting edges of saw blade to cut at all. Throughout The application. Cutting to The hydraulic system to control a tension in a blade. Adjusted by hand. Or hydraulic adjustment of a spacing of a wheel. Structural strength. an machine can be installed on an factory floor.
3. Vertical Band Saw (Vertical Band Saw).
a vertical band saw. A saw blade with a vertical line. Thare will rotate an cutting continues. an cut off light in all looks like a flat iron or steel may be lacking. Or cut into various shapes which The oanr saws can not.
an band saw different from saws seizures. an cutting am continuing. While Mills was responsible for cutting off only a stroke. The use of The saw blade am limited by The use of a centralized blade only.
an band saw blade has a thickness less than oTher types of materials, resulting in a loss of less than
Vertical band saw. Provides several features to work. Similar to carve by hand. Which are not found in oar metals such as saws, cut into geometric shapes.
4. Saw (Circular Saw or Radius Saw).
a circular saw. an circular saw are a saw blade with teeth around an band can be cut continuously. Often, some parts such as aluminum, can cut both a upright and tilted at an angle.
Security threat in The circular saw.
Saw a lot of harm. To cover up a saw.
Do not be impatient to exert control, overload cut.
First, a careful piece of work. Force because of lack of control a little easier to cut.
Always check a blade, but tough. Or stick a sharp saw.
ไม่มีความคิดเห็น:
แสดงความคิดเห็น